cjenik brodogradilišta

1. Lifting and trasportation of ship to the shore standing place, putting on proper supports and
launching in the sea (after completion of works) including use of ship’ s ladder:

Ship's lenth overall (m)	DM	Length overall (m)			DM
up to - 5	71,50		21 - 22		942,90
5 - 6	102,90		22 - 23		1.028,60
6 - 7	122,90		23 - 24		1.114,30
7 - 8	142,90		24 - 25		1.200,00
8 - 9	177,20		25 - 26		1.285,80
9 - 10	211,50		26 - 27		1.371,50
10 - 11	245,80		27 - 28		1.457,20
11 - 12	300,00		28 - 29		1.542,90
12 - 13	354,30		29 - 30		1.628,60
13 - 14	408,60		30 - 31		1.714,30
14 - 15	462,90		31 - 32		1.800,00
15 - 16	517,20		32 - 33		1.885,80
16 - 17	571,50		33 - 34		1.971,50
17 - 18	628,60		34 - 35		2.057,20
18 - 19	685,80		35 - 36		2.142,90
19 - 20	771,50		36 - 37		2.228,60
20 - 21	857,20		over 37		2.342,90
2. Using the place on terminal:
2.1. General repairs:
- First 5 (five ) days Free of charge
- Each consecutive day for 1 m length (overall)	4,30

2.2. Major repairs or reconstruction of ship:	Free of charge
* If any delay in works occured for which
Owner is held responsible indemnity will
be charged for each delayed day /
for 1 m length (overall)	2,90

3. Using of fitting out quay
(El. source and water connection may be used)
- First three days prior to lifting and after launching	Free of charge
- Each consecutive day for 1 m length (overall)	2,90

4. Flat rate charge for daily consumption of water
and el. source
- ship's length up to 17 m					85,80/week
- ship's length over 17 m					85,80/week

5. Hire of staging arround ship (section length 4 m with
platform h=2 m and h=4 m, movable on wheels) per week					85,80

6. Drive out bilge cork, bilge discharge to tank and its disposal,
fitting of new bilge cork and lead plate					100,00
7 Cleaning and washing with fresh water (high pressure pump)
Price for 1 sqm.
7.1. Underwater hull planking					1,20
7.2. Topside, deck planking					0,90

8. Manual scrapping of undwreater hull planking - per 1 sqm					3,50
9. Painting of underwater hull planking with airless gun
(including water line):
			Work	Material	Total
9.1. Start and final works			16,90	26,00	42,90
9.2. Painting of hull planking - for 1 sqm
- first coat (HEMPEL 7655 )			1,20	3,60	4,80
- second coat (HEMPEL 7655)			1,20	4,60	5,80
- one coat ( owner’s supply)			1,20	0,30	1,50
- one coat primer (HEMPEL 1237)			1,20	3,20	4,40
10. Painting of underwater hull planking
with paint roller (include. water line)
1 sqm area
- first coat (HEMPEL 7655)			1,80	6,30	8,10
- second coat (HEMPEL 7655)			1,80	4,60	6,40
- one coat (Owner’s supply)			1,80	0,60	2,40
11. Renewal of zink anodes :
11.1. Start and final works			25,80	-	25,80
11.2. Zink anodes included
for 1 pc - weight 0,5 kg			4,30	4,90	9,20
1 kg			4,30	9,30	13,60
2 kg			5,80	17,20	23,00
3 kg			7,20	26,60	33,80
4 kg			7,20	35,80	43,00
5 kg			7,20	45,00	52,20
6 kg			8,60	52,90	61,50
8 kg			8,60	74,30	82,90
10 kg			8,60	92,90	101,50
12 kg			8,60	111,50	120,10

11.3. Zink anodes supply by Owner			Work	Material	Total
for 1 kg weight 0,5 kg			4,30	0,70	5,00
1 kg			4,30	1,30	5,60
2 kg			5,80	1,30	7,10
3 kg			7,20	2,50	9,70
4 kg			7,20	3,80	11,00
5 kg			7,20	5,00	12,20
6 kg			8,60	4,90	13,50
8 kg			8,60	10,30	18,90
10 kg			8,60	12,90	21,50
12 kg			8,60	15,50	24,10

12. Underwater valves (disconnecting, dismantling,
cleaning, washing and grinding of contact
surface and reassembling after inspection by CRS)
for 1 pc
12.1. Valves DN
1’’			50,60	3,80	54,40
1 1/4’’			50,60	3,80	54,40
1 1/2’’			67,50	3,80	71,30
2’’			67,50	7,20	74,70
2 1/2’’			84,30	7,20	91,50
3’’			101,20	7,20	108,40
12.2 Slide valves 1’’			33,80	3,80	37,60
1 1/4’’			42,20	3,80	46,00
1 1/2’’			50,60	3,80	54,40
2’’			50,60	6,60	57,20
2 1/2’’			59,00	6,60	65,60
3’’			67,50	6,60	74,10

13. Water scoop net (dismantling, cleaning and
washing and reassembling after inspection by
CRS, for 1 pc
DN
up to 2’’			42,20	3,80	46,00
1 1/2’’ to 3’’			50,60	4,20	54,80

14. Rudder blade (removing, cleaning and washing
and assembling after inspection by CRS)
Rudder shaft Dia (mm)
up to 30			67,50	1,50	69,00
31 - 40			101,20	1,50	102,70
41 - 50			151,80	1,50	153,30
51 - 60			202,30	3,30	205,60
61 - 70			252,90	3,30	256,20
71 - 80			303,50	3,30	306,80
81 - 90			370,90	5,80	376,70
91 - 100			438,30	5,80	444,10
. over 101			505,80	5,80	511,60

15. Rudder shaft ( removing, cleaning and washing
and reassembling with new packing after inspection
by CRS.
Rudder shaft Dia (mm)
up to 30			33,80	10,00	43,80
30 - 40			50,60	10,00	60,60
41 - 50			84,30	10,00	94,30
51 - 60			135,10	21,50	156,60
61 - 70			168,60	21,50	190,10
71 - 80			202,30	21,50	223,80
81 - 90			236,00	34,60	270,60
91 - 100			269,80	40,30	310,10
over 101			303,50	63,20	366,70

16. Ship’s propeller (removing,cleaning and
washing and reassembling after inspection by CRS,
tightening and securing propeller nut.
Propeller shaft Dia (mm)
up to 30			16,90	1,50	18,40
31 - 40			33,80	1,50	35,30
41 - 50			42,20	1,50	43,70
51 - 60			50,60	18,00	68,60
61 - 70			59,00	22,90	81,90
71 - 80			67,50	32,00	99,50
81 - 90			84,30	32,00	116,30
91 - 100			101,20	62,60	163,80
101 - 110			118,00	62,60	180,60
111 - 120			134,90	62,60	197,50
121 - 130			151,80	78,60	230,40
131 - 140			168,60	78,60	247,20
over 141			202,30	78,60	280,90

17. Propeller shaft (removing, cleaning and
washing and reassembling with flange connection
(alignment) and new packing after inspection by
CRS). Propeller shaft Dia (mm)
up to 30			50,60	15,50	66,10
31 - 40			67,50	15,50	83,00
41 - 50			84,30	15,50	99,80
51 - 60			134,90	18,00	152,90
61 - 70			168,60	24,30	192,90
71 - 80			202,30	37,80	240,10
81 - 90			252,90	37,80	290,70
91 - 100			303,50	53,80	357,30
101 - 110			370,90	76,00	446,90
111 - 120			438,30	76,00	514,30
121 - 130			539,50	119,50	659,00
131 - 140			674,30	119,50	793,80
over 141			809,20	119,50	928,70

18. Intermediate shaft (removing of bolt and
flange, bearing,drawing out of shaft, cleaning
and washing and reassembling of flange, bearing
and connection with shaft and main engine after
inspection by CRS.
Intermediate shaft Dia (mm)			Work	Material	Total
up to 50			67,50	12,00	79,50
51 - 60			84,30	12,00	96,30
61 - 70			134,90	12,00	146,90
71 - 80			151,80	19,80	171,60
81 - 90			168,60	19,80	188,40
91 - 100			202,30	19,80	222,10
101 - 110			236,00	26,90	262,90
111 - 120			303,50	26,90	330,40
121 - 130			370,90	26,90	397,80
over 131			438,30	26,90	465,20

19. Disconnection of propeller shaft from
gearbox, and after work
inspection of alignment and connection with
gearbox (tightening).
Propeller shaft Dia (mm)
up to 30			33,80	3,20	37,00
31 - 40			42,20	3,20	45,40
41 - 50			50,60	3,20	53,80
51 - 60			59,00	5,90	64,90
61 - 70			67,50	5,90	73,40
71 - 80			84,30	5,90	90,20
81 - 90			101,20	5,90	107,10
91 - 100			134,90	8,90	143,80
101 - 110			168,60	8,90	177,50
111 - 120			202,30	8,90	211,20
121 - 130			236,00	11,50	247,50
131 - 140			269,80	11,50	281,30
over 141			337,20	11,50	348,70

20. Measurement of clearance on propeller	28,60
and rudder shaft bearings	28,60

21. Renewal of packing

Propeller shaft Dia (mm)			Work	Material	Total

	up 30	4x4	16,90	1,50	18,40
	31 - 40	4x4	16,90	1,50	18,40
		6x6	16,90	3,60	20,50
	41 - 50	4x4	25,30	1,50	26,80
		6x6	25,30	3,60	28,90
		8x8	25,30	7,20	32,50
	51 - 60	4x4	33,80	1,50	35,30
		6x6	33,80	3,60	37,40
		8x8	33,80	7,20	41,00
	61 - 70	4x4	33,80	2,30	36,10
		6x6	33,80	4,30	38,10
		8x8	33,80	8,60	42,40
	71 - 80	6x6	42,20	5,00	47,20
		8x8	42,20	9,30	51,50
		10x10	42,20	13,60	55,80
	81 - 90	6x6	42,20	5,00	47,20
		8x8	42,20	10,00	52,20
		10x10	42,20	15,00	57,20
		12x12	42,20	20,00	62,20
	91 - 100	8x8	50,60	11,50	62,10
		10x10	50,60	16,50	67,10
		12x12	50,60	22,20	72,80
		14x14	50,60	28,60	79,20
	101 - 110	10x10	50,60	17,20	67,80
		12x12	50,60	22,90	73,50
		14x14	50,60	30,80	81,40
		16x16	50,60	38,60	89,20
	111 - 120	10x10	59,00	18,60	77,60
		12x12	59,00	25,00	84,00
		14x14	59,00	33,60	92,60
		16x16	59,00	42,90	101,90
		18x18	59,00	57,20	116,20
	121 - 130	12x12	67,50	28,60	96,10
		14x14	67,50	37,20	104,70
		16x16	67,50	45,80	113,30
		18x18	67,50	62,90	130,40
		20x20	67,50	78,60	146,10
	131 - 140	14x14	84,30	38,60	122,90
		16x16	84,30	47,90	132,20
		18x18	84,30	66,50	150,80
		20x20	84,30	82,20	166,50